Home / Blog

How to Prevent Pipes From Freezing During Winter

November 17, 2026 · 9 min read

Close-up of vintage outdoor plumbing taps on a brick wall, black and white.

You prevent pipes from freezing by keeping them warm, keeping water moving, and sealing the cold air out before temperatures drop below 20°F. The three highest-impact moves are insulating exposed pipes, running a trickle of water on the coldest nights, and never letting your thermostat fall below 55°F. This guide covers exactly how to do each one, which pipes in your United States home are most vulnerable, and when a frozen line has already turned into a job for an emergency plumber.

We have thawed and repaired thousands of frozen lines across the United States, and the pattern is always the same: the homeowners who prepare in November spend the winter watching football. The ones who wait spend it watching a ceiling drip. Here is how to be in the first group.

Why Pipes Freeze and What It Costs You

Water expands about 9% when it freezes, and that expansion is what splits copper, PEX, and CPVC. A pipe does not have to burst at the frozen spot - pressure between the ice block and a closed faucet is what usually causes the failure, which is why the break often happens feet away from where the ice actually formed. That is also why a pipe can look fine, thaw, and then spray water across your basement the moment you turn the handle.

Typical 2026 pricing for a frozen-pipe repair in the United States runs $350 to $1,200 for a single accessible line, and $1,500 to $4,000 or more when the pipe is inside a wall or ceiling and drywall has to come out. Add water damage remediation and you are looking at $5,000 to $15,000 on a bad one. Insurance often covers the damage but not the repair itself, so prevention is the cheaper side of the ledger every time.

Freezing risk starts at 32°F, but pipes in exterior walls, crawlspaces, and attics freeze fast once the outdoor temperature drops below 20°F for four or more hours. Wind makes it worse. A 15 mph wind at 20°F pulls heat out of an uninsulated pipe about twice as fast as still air at the same temperature.

Which Pipes Are Most at Risk in Your Home?

Pipes on exterior walls, in unheated crawlspaces, in attics, and inside garage walls freeze first. The three most common freeze points we see are the supply line to an outdoor spigot, the line feeding a kitchen sink on an exterior wall, and the main line coming into the house through the foundation. If your home was built before 1990, odds are good that at least one of those runs is uninsulated.

Homes in colder regions are more exposed. We get a lot of calls from Emergency Plumber across the United States customers in the upper Midwest and Northeast, where a January cold snap can hold below 10°F for a week straight. In those areas, even a well-insulated home needs active measures - a trickle of water and a thermostat you do not touch.

If your home has a crawlspace, walk it before the first freeze. Look for pipes that run along the rim joist, any line that sits within 6 inches of a foundation vent, and any pipe that has already been wrapped in old, crumbling foam. That old foam is worse than nothing because it traps moisture against the pipe and hides the problem until it splits.

Insulation and Heat Tape: The First Line of Defense

Pipe insulation and self-regulating heat tape are the two most effective tools you can install yourself. Foam pipe sleeves cost $1 to $3 per linear foot and take about 30 minutes to install on an accessible run. Heat tape runs $25 to $80 for a 6- to 12-foot cable and plugs into a standard outlet. Together they handle almost every residential freeze scenario short of a multi-day power outage.

Here is the order we recommend:

  1. Seal the air first. Use expanding foam or caulk to close gaps around pipes where they penetrate exterior walls, foundation sills, and vented crawlspace openings. Cold air moving across a pipe is the single biggest freeze accelerant.
  2. Insulate every accessible pipe. Slide foam sleeves over the full run, including elbows. Miter the corners so there are no gaps. Tape the seams with acrylic tape, not duct tape - duct tape dries out and falls off within a season.
  3. Add heat tape on the worst runs. Wrap the cable in a spiral, about one wrap every inch, and never overlap the cable on itself. Overlapping causes hot spots that can melt PEX. Plug it into a GFCI outlet and, ideally, a thermostat-controlled adapter that kicks on at 40°F.
  4. Insulate over the heat tape. Heat tape without insulation on top loses most of its heat to the surrounding air. Fiberglass wrap rated for pipe use is the standard choice.

If you have a pipe that has already frozen and thawed once, treat it as compromised. Copper work-hardens at the freeze point and will split the second time. That is a job for burst pipe repair before the next cold front, not after.

Smart Thermostat and Daily Habits That Keep Water Moving

Keep your thermostat at 55°F or higher at all times, day and night, for the entire heating season. The old advice about dropping the temperature to 50°F overnight to save on heating bills is a false economy - a single burst pipe costs more than a decade of those savings. If you have a smart thermostat, disable the eco mode that lets the house drift below 55°F when you are away.

On nights when the forecast drops below 20°F, open the cabinet doors under every sink that sits against an exterior wall. That lets room air circulate around the trap and supply lines. Then let a pencil-thin stream of water run from the faucet furthest from your main shutoff. Moving water freezes much more slowly than standing water, and the cost of that trickle is a few dollars a month.

Two more habits that pay off:

  • Disconnect garden hoses and shut off outdoor spigots. A hose left connected traps water in the spigot body and the line behind it. That is the number one cause of freeze-related emergency plumbing repair calls we run in November and December.
  • Know where your main shutoff is. If a pipe does burst, every second you spend hunting for the valve is water on your floor. Tag it, test it, and make sure everyone in the house knows how to turn it.

Outdoor and Vacation Prep Before the First Hard Freeze

If you are leaving town for more than two days between November and March, do not just turn the heat down and go. Either keep the thermostat at 55°F or higher, or drain the whole system. Draining means shutting off the main, opening every faucet from the top floor down, and blowing out the lines with compressed air if you have a sprinkler system or exterior spigots.

For a weekend trip, the 55°F thermostat setting is enough. For a two-week trip in a cold climate, drain the system or have someone walk through the house every other day. We have walked into too many homes in February where a pipe let go on day three of a two-week vacation and the water ran for eleven days. The repair bill on those is never small.

Before the first hard freeze, also check the supply line to your water heater if it runs through a garage or unheated utility room. Those lines are easy to forget and they freeze just as fast as anything else. If your water heater is on its last legs, a cold snap is when it will fail - that is a call for emergency water heater repair, not a wait-and-see.

Common Mistakes That Lead to Burst Pipes

The mistakes that cause the most damage are almost always about what people do after the freeze, not before it. Here are the ones we see most often:

  • Using an open flame to thaw a pipe. A propane torch or heat gun on a frozen line will crack copper and melt PEX in seconds. Use a hair dryer on low, a space heater aimed at the cavity, or warm towels. Never a flame.
  • Pouring boiling water down a frozen drain. It can crack a porcelain fixture or a cast-iron trap. Warm water, in stages, is the safe move.
  • Leaving the thermostat in eco mode while away. A 45°F house is a frozen-pipe house. Set the floor at 55°F and leave it.
  • Ignoring a slow drain in winter. A drain that slows down when it is cold outside is often a sign of ice forming in the vent stack or the trap. That is the early warning before a full blockage.
  • Skipping the crawlspace. Out of sight, out of mind - until the pipe splits and you find out when the water bill triples.

If you have already had one freeze this season, do not assume you got lucky because nothing burst. The pipe has been stressed. Have it inspected before the next cold front.

When to Call a Professional

Call a plumber the moment you see water where it should not be, hear a hiss or spray behind a wall, or lose water pressure across the whole house during a freeze. Those are signs the pipe has already failed. Turn off the main shutoff first, then call. If you cannot find the shutoff or the leak is near electrical wiring, get out of the affected area and call from a dry room.

At Peak Plumbing Pros, we handle frozen and burst lines, thawing, and the repair that follows. We find the break, fix it, and test the line before we leave. If you have a crawlspace full of old foam insulation or a pipe that has frozen twice in the same spot, we will tell you what needs to change so it does not happen a third time.

Frequently Asked Questions

At what temperature do pipes freeze?

Pipes begin to freeze at 32°F, but the real risk starts when outdoor temperatures stay below 20°F for four or more hours. Pipes in exterior walls, crawlspaces, and attics can freeze even faster. Wind speeds above 15 mph accelerate heat loss and shorten that window considerably.

Should I leave a faucet dripping to prevent frozen pipes?

Yes - a pencil-thin stream from the faucet furthest from your main shutoff keeps water moving and slows freezing. Do this on nights when the forecast drops below 20°F. The added cost is a few dollars a month, far less than a single burst-pipe repair.

How much does it cost to fix a frozen pipe in 2026?

Typical 2026 pricing in the United States runs $350 to $1,200 for an accessible line and $1,500 to $4,000 or more when the pipe is inside a wall. Water damage remediation can add $5,000 to $15,000. Prevention costs a fraction of that.

Can I thaw a frozen pipe myself?

Yes, if the pipe is accessible and you can see it. Use a hair dryer on low, a space heater aimed at the cavity, or warm towels. Never use an open flame or a heat gun. If the pipe is inside a wall or you cannot find the freeze point, call a plumber.

Will pipe insulation alone stop pipes from freezing?

No. Insulation slows heat loss but does not add heat. It works best combined with heat tape on vulnerable runs and a thermostat kept at 55°F or higher. For pipes in unheated crawlspaces, insulation plus self-regulating heat tape is the standard setup.

Get Help with Emergency Plumber in the United States

If a pipe has already frozen, burst, or started leaking, do not wait for it to thaw on its own. Call Peak Plumbing Pros at (844) 924-8548 and we will get a licensed plumber to your door fast.

We handle frozen lines, burst pipe repair, and the cleanup that follows - so you can get back to a dry house and normal water pressure.

Frequently asked questions

At what temperature do pipes freeze?

Pipes begin to freeze at 32°F, but the real risk starts when outdoor temperatures stay below 20°F for four or more hours. Pipes in exterior walls, crawlspaces, and attics can freeze even faster. Wind speeds above 15 mph accelerate heat loss and shorten that window considerably.

Should I leave a faucet dripping to prevent frozen pipes?

Yes - a pencil-thin stream from the faucet furthest from your main shutoff keeps water moving and slows freezing. Do this on nights when the forecast drops below 20°F. The added cost is a few dollars a month, far less than a single burst-pipe repair.

How much does it cost to fix a frozen pipe in 2026?

Typical 2026 pricing in the United States runs $350 to $1,200 for an accessible line and $1,500 to $4,000 or more when the pipe is inside a wall. Water damage remediation can add $5,000 to $15,000. Prevention costs a fraction of that.

Can I thaw a frozen pipe myself?

Yes, if the pipe is accessible and you can see it. Use a hair dryer on low, a space heater aimed at the cavity, or warm towels. Never use an open flame or a heat gun. If the pipe is inside a wall or you cannot find the freeze point, call a plumber.

Will pipe insulation alone stop pipes from freezing?

No. Insulation slows heat loss but does not add heat. It works best combined with heat tape on vulnerable runs and a thermostat kept at 55°F or higher. For pipes in unheated crawlspaces, insulation plus self-regulating heat tape is the standard setup.

← All articles